74ACT16374TTR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 48-TFSOP (0.240, 6.10mm Width) |
| Number of Pins | 48 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 48 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ACT163 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 120MHz |
| Propagation Delay | 6.7 ns |
| Turn On Delay Time | 4.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 24mA 24mA |
| Max Propagation Delay @ V, Max CL | 6.7ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.6pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Width | 6.1mm |
| RoHS Status | Non-RoHS Compliant |
74ACT16374TTR Overview
The flip flop is packaged in a case of 48-TFSOP (0.240, 6.10mm Width). You can find it in the Tape & Reel (TR)package. T flip flop uses Tri-State, Non-Invertedas its output configuration. This trigger uses the value Positive Edge. Surface Mountmounts this electrical part. With a supply voltage of 4.5V~5.5V volts, it operates. Temperature is set to -55°C~125°C TA. Logic flip flops of this type are classified as D-Type. FPGAs belonging to the 74ACTseries contain this type of chip. Its output frequency should not exceed 120MHz. There are 2 elements in it. There is 8μA quiescent consumption. 48terminations have occurred. D latch belongs to the 74ACT163 family. The power source is powered by 5V. The input capacitance of this T flip flop is 3.6pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. Electronic devices of this type belong to the ACTfamily. In this case, the electronic component is mounted in the way of Surface Mount. It is designed with 48 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. 8bits are used in its design. As soon as 5.5Vis reached, Vsup reaches its maximum value. Normally, the supply voltage (Vsup) should be kept above 4.5V. The superior flexibility of this circuit is achieved by using 8 circuits. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. The D latch operates on 5V volts. The D flip flop is embedded with 2ports. There are 3 output lines on it.
74ACT16374TTR Features
Tape & Reel (TR) package
74ACT series
48 pins
8 Bits
5V power supplies
74ACT16374TTR Applications
There are a lot of STMicroelectronics 74ACT16374TTR Flip Flops applications.
- Single Up Count-Control Line
- Control circuits
- Asynchronous counter
- Differential Individual
- Parallel data storage
- Common Clocks
- Shift registers
- Bus hold
- Shift Registers
- Load Control
