74ACT174SJX
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-SOP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ACT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 200MHz |
| Base Part Number | 74ACT174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 7 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 6 |
| Clock Frequency | 200MHz |
| Propagation Delay | 10.5 ns |
| Turn On Delay Time | 7 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 6 |
| Max Propagation Delay @ V, Max CL | 10.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 6 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74ACT174SJX Overview
The flip flop is packaged in 16-SOIC (0.209, 5.30mm Width). D flip flop is embedded in the Tape & Reel (TR) package. There is a Non-Invertedoutput configured with it. In the configuration of the trigger, Positive Edgeis used. There is an electric part mounted in the way of Surface Mount. It operates with a supply voltage of 4.5V~5.5V. A temperature of -40°C~85°C TAis used in the operation. Logic flip flops of this type are classified as D-Type. JK flip flop belongs to the 74ACTseries of FPGAs. You should not exceed 200MHzin the output frequency of the device. There are 1 elements in it. This process consumes 40μA quiescents. Members of the 74ACT174family make up this object. There is 4.5pF input capacitance for this T flip flop. This electronic part is mounted in the way of Surface Mount. The 16pins are designed into the board. A Positive Edgeclock edge trigger is used in this device. An electronic part with 6bits has been designed. Despite its superior flexibility, it relies on 7 circuits to achieve it. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. The JK flip flop is with 6 output lines to operate. There are 3 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. -24mAis set as the high level output current. In the low level output current setting, 24mAis used. If the operating temperature is lower than 85°C, it is recommended. Ideally, the operating temperature should be higher than -40°C. Initially, it requires a voltage of 4.5V as the minimum supply voltage. In this case, it supports a maximum supply voltage of 5.5V. This frequency can be achieved 200MHz.
74ACT174SJX Features
Tape & Reel (TR) package
74ACT series
16 pins
6 Bits
74ACT174SJX Applications
There are a lot of ON Semiconductor 74ACT174SJX Flip Flops applications.
- Latch
- Common Clocks
- Data transfer
- 2 – Bit synchronous counter
- Memory
- Patented noise
- Single Up Count-Control Line
- Balanced 24 mA output drivers
- Shift Registers
- Parallel data storage
