74ACT175SCX
| Parameters | |
|---|---|
| Packaging | Tape & Reel (TR) |
| Series | 74ACT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 236MHz |
| Base Part Number | 74ACT175 |
| Function | Master Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 4 |
| Clock Frequency | 236MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 6 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 4 |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-SOIC |
| Operating Temperature | -40°C~85°C TA |
74ACT175SCX Overview
The flip flop is packaged in a case of 16-SOIC (0.154, 3.90mm Width). The Tape & Reel (TR)package contains it. T flip flop uses Differentialas its output configuration. The trigger it is configured with uses Positive Edge. Surface Mountis positioned in the way of this electronic part. The JK flip flop operates at 4.5V~5.5Vvolts. Currently, the operating temperature is -40°C~85°C TA. This D latch has the type D-Type. The FPGA belongs to the 74ACT series. There should be no greater frequency than 236MHzon its output. A total of 1elements are present in it. As a result, it consumes 40μA quiescent current and is not affected by external forces. It is a member of the 74ACT175 family. Its input capacitance is 4.5pFfarads. There is an electronic part mounted in the way of Surface Mount. This board has 16 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. An electronic part with 4bits has been designed. Despite its superior flexibility, it relies on 4 circuits to achieve it. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. There are 2 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code. As of now, there are 1input lines. The high level output current is set to -24mA. There is 24mA output current at the low level. If the operating temperature is lower than 85°C, it is recommended. It is recommended that the operating temperature is higher than -40°C. The minimum voltage required for operation is 4.5V. There is a maximum voltage support of 5.5V. This frequency can be achieved 236MHz.
74ACT175SCX Features
Tape & Reel (TR) package
74ACT series
16 pins
4 Bits
74ACT175SCX Applications
There are a lot of ON Semiconductor 74ACT175SCX Flip Flops applications.
- Synchronous counter
- Data Synchronizers
- Bus hold
- Divide a clock signal by 2 or 4
- Cold spare funcion
- Latch-up performance
- Counters
- Balanced Propagation Delays
- Consumer
- Memory
