74ACT273MTC
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-TSSOP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1998 |
| Series | 74ACT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 189MHz |
| Base Part Number | 74ACT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 189MHz |
| Propagation Delay | 8.5 ns |
| Turn On Delay Time | 6.5 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74ACT273MTC Overview
The flip flop is packaged in a case of 20-TSSOP (0.173, 4.40mm Width). It is included in the package Tube. T flip flop uses Non-Invertedas its output configuration. Positive Edgeis the trigger it is configured with. Surface Mountis occupied by this electronic component. A voltage of 4.5V~5.5Vis used as the supply voltage. In this case, the operating temperature is -40°C~85°C TA. This logic flip flop is classified as type D-Type. In FPGA terms, D flip flop is a type of 74ACTseries FPGA. You should not exceed 189MHzin the output frequency of the device. The list contains 1 elements. During its operation, it consumes 40μA quiescent energy. The 74ACT273 family contains this object. The input capacitance of this T flip flop is 4.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. Electronic part Surface Mountis mounted in the way. The electronic flip flop is designed with pins 20. This device's clock edge trigger type is Positive Edge. This flip flop is designed with 8 Bits. Despite its superior flexibility, it relies on 8 circuits to achieve it. For high efficiency, the supply voltage should be kept at 5V. It operates with 8 output lines. This input has 3lines in it. High level output current is set to -24mA. In the low level output current setting, the current is set to 24mA. It is recommended that the operating temperature be below 85°C. Temperatures above -40°Cshould be used. The RS flip flop is designed to operate with a minimal supply voltage of 4.5VV. 5.5Vis the maximum supply voltage it supports. It is possible to achieve a frequency of 189MHz.
74ACT273MTC Features
Tube package
74ACT series
20 pins
8 Bits
74ACT273MTC Applications
There are a lot of ON Semiconductor 74ACT273MTC Flip Flops applications.
- Bounce elimination switch
- Synchronous counter
- Memory
- Computers
- Power down protection
- Functionally equivalent to the MC10/100EL29
- Latch
- Frequency Dividers
- Bus hold
- Automotive
