74ACT377PC
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Supplier Device Package | 20-PDIP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1998 |
| Series | 74ACT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 175MHz |
| Base Part Number | 74ACT377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 175MHz |
| Propagation Delay | 10 ns |
| Turn On Delay Time | 6.5 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 10ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 8 |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74ACT377PC Overview
The flip flop is packaged in 20-DIP (0.300, 7.62mm). It is included in the package Tube. T flip flop uses Non-Invertedas the output. In the configuration of the trigger, Positive Edgeis used. There is an electronic component mounted in the way of Through Hole. The supply voltage is set to 4.5V~5.5V. It is operating at a temperature of -40°C~85°C TA. It is an electronic flip flop with the type D-Type. FPGAs belonging to the 74ACTseries contain this type of chip. In order for it to function properly, its output frequency should not exceed 175MHz. D latch consists of 1 elements. It consumes 40μA of quiescent It is a member of the 74ACT377 family. This T flip flop has a capacitance of 4.5pF farads at the input. Through Hole mounts this electronic component. It is designed with 20 pins. This device has Positive Edgeas its clock edge trigger type. Flip flops designed with 8bits are used in this part. Using 8 circuits, it is highly flexible. In order to ensure high efficiency, the supply voltage should remain at 5V. There are no output lines on the JK flip flop. There are 8 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. There is -24mA output current at the high level. In the low level output current setting, 24mAis used. Ideally, the operating temperature should be below 85°C. Ideally, the operating temperature should be higher than -40°C. It operates with the minimal supply voltage of 4.5V. There is a maximum voltage support of 5.5V. It is possible to achieve 175MHz frequencies.
74ACT377PC Features
Tube package
74ACT series
20 pins
8 Bits
74ACT377PC Applications
There are a lot of ON Semiconductor 74ACT377PC Flip Flops applications.
- Single Down Count-Control Line
- Buffer registers
- Control circuits
- Asynchronous counter
- ATE
- Circuit Design
- Parallel data storage
- Latch
- Storage registers
- Guaranteed simultaneous switching noise level
