74ACT574TTR
| Parameters | |
|---|---|
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 10ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ACT574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 270MHz |
| Propagation Delay | 10 ns |
| Turn On Delay Time | 5 ns |
74ACT574TTR Overview
As a result, it is packaged as 20-TSSOP (0.173, 4.40mm Width). The Tape & Reel (TR)package contains it. Currently, the output is configured to use Tri-State, Non-Inverted. It is configured with a trigger that uses Positive Edge. There is an electronic component mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. Temperature is set to -55°C~125°C TA. This logic flip flop is classified as type D-Type. The 74ACTseries comprises this type of FPGA. You should not exceed 270MHzin its output frequency. The list contains 1 elements. As a result, it consumes 4μA quiescent current. There are 20 terminations,If you search by 74ACT574, you will find similar parts. Power is provided by a 5V supply. Its input capacitance is 4pFfarads. An electronic device belonging to the family ACTcan be found here. It is mounted by the way of Surface Mount. As you can see from the design, it has pins with 20. There is a clock edge trigger type of Positive Edgeon this device. This device is part of the FF/Latchesbase part number family. This flip flop is designed with 8 Bits. In order to achieve its superior flexibility, 8 circuits are used. As a result of its reliability, this D flip flop is ideally suited for TAPE AND REEL. The D latch runs on a voltage of 5V volts. This flip flop has a total of 2ports. Optimal efficiency requires a supply voltage of 5V. There are 3 output lines in this JK flip flop.
74ACT574TTR Features
Tape & Reel (TR) package
74ACT series
20 pins
8 Bits
5V power supplies
74ACT574TTR Applications
There are a lot of STMicroelectronics 74ACT574TTR Flip Flops applications.
- Counters
- Storage Registers
- Dynamic threshold performance
- Parallel data storage
- Single Up Count-Control Line
- Balanced 24 mA output drivers
- Consumer
- Guaranteed simultaneous switching noise level
- Frequency division
- Test & Measurement
