74ACT74PC
| Parameters | |
|---|---|
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 210MHz |
| Base Part Number | 74ACT74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Output Current | 24mA |
| Number of Bits | 2 |
| Clock Frequency | 210MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 7.5 ns |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 20μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Gates | 2 |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Supplier Device Package | 14-PDIP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ACT |
74ACT74PC Overview
The item is packaged in 14-DIP (0.300, 7.62mm)cases. Package Tubeembeds it. Differentialis the output configured for it. In the configuration of the trigger, Positive Edgeis used. There is an electric part mounted in the way of Through Hole. The supply voltage is set to 4.5V~5.5V. In this case, the operating temperature is -40°C~85°C TA. There is D-Type type of electronic flip flop associated with this device. In this case, it is a type of FPGA belonging to the 74ACT series. Its output frequency should not exceed 210MHz Hz. The element count is 2 . As a result, it consumes 20μA quiescent current. It is a member of the 74ACT74 family. The input capacitance of this JK flip flopis 4.5pF farads. Through Hole mounts this electronic component. It is designed with 14 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. It is designed with a number of bits of 2. The superior flexibility is achieved through the use of 2 circuits. For high efficiency, the supply voltage should be kept at 5V. With an output current of 24mA, it is possible to design the device in any way you want. There are 1 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code. The number of input lines is 1. High level output current is set to -24mA. There is no low level output current set at 24mA. It is recommended that the operating temperature be lower than 85°C. It is recommended that the operating temperature is higher than -40°C. Normally, it operates with a voltage of 4.5VV as its minimum supply voltage. 5.5Vis the maximum supply voltage supported by it. A frequency of 210MHzcan be achieved. 2 gates constitute its basic building block.
74ACT74PC Features
Tube package
74ACT series
14 pins
2 Bits
2 gates
74ACT74PC Applications
There are a lot of ON Semiconductor 74ACT74PC Flip Flops applications.
- Data Synchronizers
- Latch-up performance
- QML qualified product
- Bus hold
- Convert a momentary switch to a toggle switch
- Storage Registers
- Circuit Design
- Buffer registers
- Memory
- Reduced system switching noise
