74ACT821MTCX
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 24 |
| Supplier Device Package | 24-TSSOP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| Series | 74ACT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 150MHz |
| Base Part Number | 74ACT821 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 10 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 10 |
| Clock Frequency | 150MHz |
| Propagation Delay | 9.5 ns |
| Turn On Delay Time | 6 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 80μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 10 |
| Max Propagation Delay @ V, Max CL | 9.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 10 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74ACT821MTCX Overview
The flip flop is packaged in a case of 24-TSSOP (0.173, 4.40mm Width). You can find it in the Tape & Reel (TR)package. As configured, the output uses Tri-State, Non-Inverted. In the configuration of the trigger, Positive Edgeis used. This electronic part is mounted in the way of Surface Mount. A supply voltage of 4.5V~5.5V is required for operation. A temperature of -40°C~85°C TAis considered to be the operating temperature. A flip flop of this type is classified as a D-Type. This type of FPGA is a part of the 74ACT series. You should not exceed 150MHzin its output frequency. A total of 1elements are contained within it. Despite external influences, it consumes 80μAof quiescent current. This D latch belongs to the family of 74ACT821. This JK flip flop has a 4.5pFfarad input capacitance. This electronic part is mounted in the way of Surface Mount. This board is designed with 24pins on it. A Positive Edgeclock edge trigger is used in this device. There are 10bits in its design. Despite its superior flexibility, it relies on 10 circuits to achieve it. For high efficiency, the supply voltage should be set to 5V. It has 3 output lines to operate. There are 10 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. A -24mAis set for the high level output current. There is 24mA output current at the low level. Operating temperatures should be lower than 85°C. In order for the system to operate properly, the temperature should be higher than -40°C. The minimum voltage required for operation is 4.5V. There is a maximum supply voltage of 5.5V. We are able to achieve a frequency of 150MHz.
74ACT821MTCX Features
Tape & Reel (TR) package
74ACT series
24 pins
10 Bits
74ACT821MTCX Applications
There are a lot of ON Semiconductor 74ACT821MTCX Flip Flops applications.
- Data transfer
- Control circuits
- Parallel data storage
- Single Up Count-Control Line
- Count Modes
- Buffered Clock
- Storage Registers
- Event Detectors
- Frequency Divider circuits
- Storage registers
