74ACT825SCX
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 24 |
| Supplier Device Package | 24-SOP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ACT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 158MHz |
| Base Part Number | 74ACT825 |
| Function | Master Reset |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 158MHz |
| Propagation Delay | 9.5 ns |
| Turn On Delay Time | 5.5 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 80μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 9.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 8 |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74ACT825SCX Overview
It is embeded in 24-SOIC (0.295, 7.50mm Width) case. It is included in the package Tape & Reel (TR). T flip flop is configured with an output of Tri-State, Non-Inverted. In the configuration of the trigger, Positive Edgeis used. There is an electric part mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. In this case, the operating temperature is -40°C~85°C TA. It is an electronic flip flop with the type D-Type. FPGAs belonging to the 74ACTseries contain this type of chip. It should not exceed 158MHzin its output frequency. D latch consists of 1 elements. T flip flop consumes 80μA quiescent energy. D latch belongs to the 74ACT825 family. There is 4.5pF input capacitance for this T flip flop. It is mounted by the way of Surface Mount. The electronic flip flop is designed with pins 24. A Positive Edgeclock edge trigger is used in this device. 8bits are used in its design. Despite its superior flexibility, it relies on 8 circuits to achieve it. For high efficiency, the supply voltage should be kept at 5V. To operate, the chip has a total of 8 output lines. This input has 8lines in it. In this case, the high level output current is set to -24mA. There is 24mA output current at the low level. Operating temperatures should be lower than 85°C. In order for the system to operate properly, the temperature should be higher than -40°C. Normally, it operates with a voltage of 4.5VV as its minimum supply voltage. It supports the maximal supply voltage of 5.5V. It is possible to obtain a frequency of 158MHz.
74ACT825SCX Features
Tape & Reel (TR) package
74ACT series
24 pins
8 Bits
74ACT825SCX Applications
There are a lot of ON Semiconductor 74ACT825SCX Flip Flops applications.
- Set-reset capability
- Parallel data storage
- Modulo – n – counter
- Synchronous counter
- Balanced 24 mA output drivers
- Pattern generators
- Circuit Design
- Storage registers
- Shift Registers
- Power down protection
