74ACTQ16374MTD
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 48-TFSOP (0.240, 6.10mm Width) |
| Number of Pins | 48 |
| Supplier Device Package | 48-TSSOP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ACTQ |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 71MHz |
| Base Part Number | 74ACTQ16374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Number of Circuits | 16 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 16 |
| Clock Frequency | 71MHz |
| Propagation Delay | 7.9 ns |
| Turn On Delay Time | 5.1 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 80μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 7.9ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 8 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74ACTQ16374MTD Overview
The item is packaged in 48-TFSOP (0.240, 6.10mm Width)cases. There is an embedded version in the package Tube. T flip flop uses Tri-State, Non-Invertedas the output. It is configured with a trigger that uses a value of Positive Edge. It is mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis required for its operation. Currently, the operating temperature is -40°C~85°C TA. It belongs to the type D-Typeof flip flops. JK flip flop belongs to the 74ACTQseries of FPGAs. You should not exceed 71MHzin the output frequency of the device. D latch consists of 2 elements. This process consumes 80μA quiescents. The 74ACTQ16374family includes it. Input capacitance of this device is 4.5pF farads. There is an electronic part mounted in the way of Surface Mount. With its 48pins, it is designed to work with most electronic flip flops. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. 16bits are used in its design. Despite its superior flexibility, it relies on 16 circuits to achieve it. For high efficiency, the supply voltage should be set to 5V. It is designed with 3 output lines. It has 8lines. A -24mAis set for the high level output current. It is set to 24mAfor the low level output current. The operating temperature should be lower than 85°C. It is recommended that the operating temperature is higher than -40°C. Normally, it operates with a voltage of 4.5VV as its minimum supply voltage. It supports a maximum supply voltage of 5.5V volts. It is possible to obtain a frequency of 71MHz.
74ACTQ16374MTD Features
Tube package
74ACTQ series
48 pins
16 Bits
74ACTQ16374MTD Applications
There are a lot of ON Semiconductor 74ACTQ16374MTD Flip Flops applications.
- Bus hold
- Clock pulse
- Communications
- Differential Individual
- 2 – Bit synchronous counter
- EMI reduction circuitry
- Latch-up performance
- Matched Rise and Fall
- Memory
- Storage Registers
