74AHC273PW-Q100J
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Series | 74AHC |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74AHC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Min (Vsup) | 2V |
| Clock Frequency | 110MHz |
| Propagation Delay | 21.5 ns |
| Family | AHC/VHC/H/U/V |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 10.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74AHC273PW-Q100J Overview
It is embeded in 20-TSSOP (0.173, 4.40mm Width) case. It is included in the package Tape & Reel (TR). T flip flop uses Non-Invertedas the output. The trigger configured with it uses Positive Edge. Surface Mountis positioned in the way of this electronic part. Powered by a 2V~5.5Vvolt supply, it operates as follows. In the operating environment, the temperature is -40°C~125°C TA. This D latch has the type D-Type. FPGAs belonging to the 74AHCseries contain this type of chip. A frequency of 110MHzshould not be exceeded by its output. A total of 1elements are contained within it. It consumes 4μA of quiescent current without being affected by external factors. A total of 20terminations have been recorded. JK flip flop belongs to 74AHC273 family. It is powered by a voltage of 5V . There is 3pF input capacitance for this T flip flop. In this case, the D flip flop belongs to the AHC/VHC/H/U/Vfamily. There is an electronic part mounted in the way of Surface Mount. This board has 20 pins. In this device, the clock edge trigger type is Positive Edge. Normal operation requires a supply voltage (Vsup) above 2V. For high efficiency, the supply voltage should be set to 5V.
74AHC273PW-Q100J Features
Tape & Reel (TR) package
74AHC series
20 pins
74AHC273PW-Q100J Applications
There are a lot of Nexperia USA Inc. 74AHC273PW-Q100J Flip Flops applications.
- ESD protection
- Frequency division
- 2 – Bit synchronous counter
- Patented noise
- Cold spare funcion
- Asynchronous counter
- QML qualified product
- Circuit Design
- Registers
- Matched Rise and Fall
