74AHC273PW,112
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2008 |
| Series | 74AHC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74AHC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Bits | 8 |
| Clock Frequency | 110MHz |
| Propagation Delay | 4.2 ns |
| Turn On Delay Time | 6 ns |
| Family | AHC |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74AHC273PW,112 Overview
In the form of 20-TSSOP (0.173, 4.40mm Width), it has been packaged. It is contained within the Tubepackage. Currently, the output is configured to use Non-Inverted. This trigger uses the value Positive Edge. There is an electronic component mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 2V~5.5V. A temperature of -40°C~125°C TAis considered to be the operating temperature. This electronic flip flop is of type D-Type. FPGAs belonging to the 74AHCseries contain this type of chip. Its output frequency should not exceed 110MHz Hz. In total, it contains 1 elements. It consumes 4μA of quiescent current without being affected by external factors. There have been 20 terminations. JK flip flop belongs to 74AHC273 family. A voltage of 5V provides power to the D latch. A 3pFfarad input capacitance is provided by this T flip flop. This D flip flop belongs to the family of AHC. Surface Mount mounts this electronic component. There are 20pins on it. It has a clock edge trigger type of Positive Edge. There are 8bits in its design. The supply voltage (Vsup) should be kept above 2V for normal operation. High efficiency requires the supply voltage to be maintained at 5V. Currently, there are 8 lines of input.
74AHC273PW,112 Features
Tube package
74AHC series
20 pins
8 Bits
74AHC273PW,112 Applications
There are a lot of Nexperia USA Inc. 74AHC273PW,112 Flip Flops applications.
- Shift Registers
- Storage Registers
- EMI reduction circuitry
- Memory
- Count Modes
- Frequency division
- Automotive
- Bus hold
- Patented noise
- ESD performance
