74AHC273PW,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | 74AHC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74AHC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Min (Vsup) | 2V |
| Output Current | 25mA |
| Number of Bits | 8 |
| Clock Frequency | 110MHz |
| Propagation Delay | 21.5 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 6 ns |
| Family | AHC |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74AHC273PW,118 Overview
The flip flop is packaged in a case of 20-TSSOP (0.173, 4.40mm Width). The Tape & Reel (TR)package contains it. As configured, the output uses Non-Inverted. Positive Edgeis the trigger it is configured with. This electronic part is mounted in the way of Surface Mount. With a supply voltage of 2V~5.5V volts, it operates. In the operating environment, the temperature is -40°C~125°C TA. This logic flip flop is classified as type D-Type. In this case, it is a type of FPGA belonging to the 74AHC series. This D flip flop should not have a frequency greater than 110MHz. A total of 1 elements are present. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. JK flip flop belongs to 74AHC273 family. A voltage of 5V is used as the power supply for this D latch. Its input capacitance is 3pFfarads. In terms of electronic devices, this device belongs to the AHCfamily of devices. The electronic part is mounted in the way of Surface Mount. This board has 20 pins. It has a clock edge trigger type of Positive Edge. Flip flops designed with 8bits are used in this part. The supply voltage (Vsup) should be kept above 2V for normal operation. The supply voltage should be maintained at 5V for high efficiency. The 25mA output current allows it to be designed with the greatest amount of flexibility. There are 8 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. 4μAquiescent current consumed.
74AHC273PW,118 Features
Tape & Reel (TR) package
74AHC series
20 pins
8 Bits
74AHC273PW,118 Applications
There are a lot of Nexperia USA Inc. 74AHC273PW,118 Flip Flops applications.
- Convert a momentary switch to a toggle switch
- Data Synchronizers
- ESD performance
- Differential Individual
- Guaranteed simultaneous switching noise level
- Automotive
- Single Down Count-Control Line
- Communications
- Count Modes
- Counters
