74AHC374PW-Q100J
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | 74AHC |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74AHC374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 120MHz |
| Propagation Delay | 10.1 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 6.4 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 8mA 8mA |
| Output Polarity | TRUE |
| Max Propagation Delay @ V, Max CL | 10.1ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74AHC374PW-Q100J Overview
It is embeded in 20-TSSOP (0.173, 4.40mm Width) case. D flip flop is embedded in the Tape & Reel (TR) package. T flip flop uses Tri-State, Non-Invertedas its output configuration. JK flip flop uses Positive Edgeas the trigger. This electronic part is mounted in the way of Surface Mount. The supply voltage is set to 2V~5.5V. The operating temperature is -40°C~125°C TA. This logic flip flop is classified as type D-Type. The 74AHCseries comprises this type of FPGA. Its output frequency should not exceed 120MHz. D latch consists of 1 elements. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. The object belongs to the 74AHC374 family. The power supply voltage is 5V. A JK flip flop with a 3pFfarad input capacitance is used here. A device of this type belongs to the family of AHC/VHC/H/U/V. This electronic part is mounted in the way of Surface Mount. There are 20pins on it. This device has Positive Edgeas its clock edge trigger type. There are 8bits in this flip flop. Normally, the supply voltage (Vsup) should be above 2V. There are 2 ports embedded in the flip flops. In order to achieve high efficiency, the supply voltage should be maintained at 5V. This input has 8lines in it. 4μAquiescent current consumed.
74AHC374PW-Q100J Features
Tape & Reel (TR) package
74AHC series
20 pins
8 Bits
74AHC374PW-Q100J Applications
There are a lot of Nexperia USA Inc. 74AHC374PW-Q100J Flip Flops applications.
- Divide a clock signal by 2 or 4
- Instrumentation
- Frequency Dividers
- Common Clocks
- Data storage
- Synchronous counter
- Registers
- Safety Clamp
- Buffered Clock
- ESD performance
