74AHC74BQ-Q100X
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-VFQFN Exposed Pad |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Series | 74AHC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74AHC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Supply Voltage-Min (Vsup) | 2V |
| Clock Frequency | 115MHz |
| Propagation Delay | 20 ns |
| Quiescent Current | 2μA |
| Family | AHC/VHC/H/U/V |
| Current - Output High, Low | 8mA 8mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 9.3ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Clock Edge Trigger Type | Positive Edge |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74AHC74BQ-Q100X Overview
The flip flop is packaged in 14-VFQFN Exposed Pad. The package Tape & Reel (TR)contains it. There is a Differentialoutput configured with it. This trigger uses the value Positive Edge. There is an electronic component mounted in the way of Surface Mount. A voltage of 2V~5.5Vis used as the supply voltage. -40°C~125°C TAis the operating temperature. This logic flip flop is classified as type D-Type. JK flip flop belongs to the 74AHCseries of FPGAs. There should be no greater frequency than 115MHzon its output. D latch consists of 2 elements. It has been determined that there have been 14 terminations. If you search by 74AHC74, you will find similar parts. A voltage of 5V is used as the power supply for this D latch. Input capacitance of this device is 3pF farads. This D flip flop belongs to the family of AHC/VHC/H/U/V. It is mounted by the way of Surface Mount. The 14pins are designed into the board. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. A normal operating voltage (Vsup) should remain above 2V. Optimal efficiency requires a supply voltage of 5V. There is 2μA quiescent current consumption by it.
74AHC74BQ-Q100X Features
Tape & Reel (TR) package
74AHC series
14 pins
74AHC74BQ-Q100X Applications
There are a lot of Nexperia USA Inc. 74AHC74BQ-Q100X Flip Flops applications.
- Consumer
- ATE
- Computing
- Bus hold
- Memory
- Circuit Design
- Parallel data storage
- Buffered Clock
- Computers
- Data storage
