74AHCT273D,112
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2008 |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74AHCT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Bits | 8 |
| Clock Frequency | 75MHz |
| Propagation Delay | 4 ns |
| Turn On Delay Time | 5.8 ns |
| Family | AHCT/VHCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 9.2ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 8 |
| fmax-Min | 65 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
74AHCT273D,112 Overview
It is embeded in 20-SOIC (0.295, 7.50mm Width) case. You can find it in the Tubepackage. There is a Non-Invertedoutput configured with it. In the configuration of the trigger, Positive Edgeis used. In this case, the electronic component is mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis required for its operation. In this case, the operating temperature is -40°C~125°C TA. D-Typeis the type of this D latch. FPGAs belonging to the 74AHCTseries contain this type of chip. Its output frequency should not exceed 75MHz Hz. A total of 1elements are present in it. T flip flop consumes 4μA quiescent energy. The number of terminations is 20. It is a member of the 74AHCT273 family. The power source is powered by 5V. Its input capacitance is 3pFfarads. In this case, the D flip flop belongs to the AHCT/VHCTfamily. In this case, the electronic component is mounted in the way of Surface Mount. This board has 20 pins. A Positive Edgeclock edge trigger is used in this device. This flip flop is designed with 8 Bits. For high efficiency, the supply voltage should be set to 5V. As of now, there are 8input lines.
74AHCT273D,112 Features
Tube package
74AHCT series
20 pins
8 Bits
74AHCT273D,112 Applications
There are a lot of Nexperia USA Inc. 74AHCT273D,112 Flip Flops applications.
- Frequency Dividers
- Bus hold
- Test & Measurement
- Synchronous counter
- Memory
- Instrumentation
- Counters
- Guaranteed simultaneous switching noise level
- Computers
- Modulo – n – counter
