74AHCT377PW-Q100J
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Series | 74AHCT |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74AHCT377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Number of Bits | 8 |
| Clock Frequency | 130MHz |
| Propagation Delay | 10.5 ns |
| Quiescent Current | 4μA |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 8mA 8mA |
| Output Polarity | TRUE |
| Max Propagation Delay @ V, Max CL | 10.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74AHCT377PW-Q100J Overview
It is embeded in 20-TSSOP (0.173, 4.40mm Width) case. It is contained within the Tape & Reel (TR)package. This output is configured with Non-Inverted. The trigger configured with it uses Positive Edge. There is an electronic component mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis used as the supply voltage. It is at -40°C~125°C TAdegrees Celsius that the system is operating. Logic flip flops of this type are classified as D-Type. FPGAs belonging to the 74AHCTseries contain this type of chip. You should not exceed 130MHzin its output frequency. D latch consists of 1 elements. Terminations are 20. This D latch belongs to the family of 74AHCT377. The power supply voltage is 5V. Its input capacitance is 3pFfarads. It is a member of the AHCT/VHCT/VTfamily of D flip flop. There is an electronic part that is mounted in the way of Surface Mount. The 20pins are designed into the board. It has a clock edge trigger type of Positive Edge. An electronic part with 8bits has been designed. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. This input has 8lines. Quiescent current is consumed by the D latch in the amount of 4μA.
74AHCT377PW-Q100J Features
Tape & Reel (TR) package
74AHCT series
20 pins
8 Bits
74AHCT377PW-Q100J Applications
There are a lot of Nexperia USA Inc. 74AHCT377PW-Q100J Flip Flops applications.
- Computers
- Synchronous counter
- Communications
- Data storage
- Matched Rise and Fall
- Supports Live Insertion
- Reduced system switching noise
- ESD protection
- Bus hold
- Balanced 24 mA output drivers
