74AHCT377PW,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-TSSOP |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | 74AHCT |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 130MHz |
| Base Part Number | 74AHCT377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Clock Frequency | 130MHz |
| Propagation Delay | 4 ns |
| Turn On Delay Time | 5.7 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 10.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -8mA |
| Input Capacitance | 3pF |
| Low Level Output Current | 8mA |
| Number of Input Lines | 8 |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74AHCT377PW,118 Overview
It is embeded in 20-TSSOP (0.173, 4.40mm Width) case. D flip flop is embedded in the Tape & Reel (TR) package. In the configuration, Non-Invertedis used as the output. This trigger uses the value Positive Edge. This electronic part is mounted in the way of Surface Mount. The supply voltage is set to 4.5V~5.5V. -40°C~125°C TAis the operating temperature. This electronic flip flop is of type D-Type. This type of FPGA is a part of the 74AHCT series. A frequency of 130MHzshould not be exceeded by its output. In total, there are 1 elements. As a result, it consumes 4μA quiescent current and is not affected by external forces. The object belongs to the 74AHCT377 family. This JK flip flop has a 3pFfarad input capacitance. Surface Mount mounts this electronic component. The electronic flip flop is designed with pins 20. In this device, the clock edge trigger type is Positive Edge. Using 1 circuits, it is highly flexible. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. The JK flip flop is with 8 output lines to operate. Currently, there are 8 lines of input. -8mAis the output current at high level. In the low level output current setting, the current is set to 8mA. A temperature below 125°Cis recommended for operation. Ideally, the operating temperature should be higher than -40°C. The minimum voltage required for operation is 4.5V. 5.5Vis the maximum supply voltage supported by it. This can be achieved at a frequency of 130MHz.
74AHCT377PW,118 Features
Tape & Reel (TR) package
74AHCT series
20 pins
74AHCT377PW,118 Applications
There are a lot of Nexperia USA Inc. 74AHCT377PW,118 Flip Flops applications.
- CMOS Process
- Computers
- Memory
- Safety Clamp
- Circuit Design
- Divide a clock signal by 2 or 4
- Single Down Count-Control Line
- Parallel data storage
- Data transfer
- Cold spare funcion
