74AHCT574PW,112
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2008 |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74AHCT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 115MHz |
| Propagation Delay | 4.4 ns |
| Turn On Delay Time | 6.3 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74AHCT574PW,112 Overview
It is packaged in the way of 20-TSSOP (0.173, 4.40mm Width). D flip flop is included in the Tubepackage. In the configuration, Tri-State, Non-Invertedis used as the output. The trigger it is configured with uses Positive Edge. Surface Mountmounts this electrical part. A voltage of 4.5V~5.5Vis required for its operation. Currently, the operating temperature is -40°C~125°C TA. This logic flip flop is classified as type D-Type. FPGAs belonging to the 74AHCTseries contain this type of chip. Its output frequency should not exceed 115MHz. In total, it contains 1 elements. This process consumes 4μA quiescents. There have been 20 terminations. If you search by 74AHCT574, you will find similar parts. Power is provided by a 5V supply. Input capacitance of this device is 3pF farads. An electronic device belonging to the family AHCT/VHCT/VTcan be found here. Electronic part Surface Mountis mounted in the way. It is designed with 20 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. There are 8bits in its design. A D flip flop with 2embedded ports is available. For high efficiency, the supply voltage should be kept at 5V. It has 8lines. Additionally, there are BROADSIDE VERSION OF 374 on the electronic flip flop that can be referred to.
74AHCT574PW,112 Features
Tube package
74AHCT series
20 pins
8 Bits
74AHCT574PW,112 Applications
There are a lot of Nexperia USA Inc. 74AHCT574PW,112 Flip Flops applications.
- Consumer
- Registers
- Divide a clock signal by 2 or 4
- Guaranteed simultaneous switching noise level
- Single Up Count-Control Line
- Memory
- Count Modes
- Individual Asynchronous Resets
- 2 – Bit synchronous counter
- Reduced system switching noise
