74AHCT74D,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74AHCT74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Clock Frequency | 140MHz |
| Propagation Delay | 3.3 ns |
| Quiescent Current | 2μA |
| Turn On Delay Time | 4.8 ns |
| Family | AHCT/VHCT |
| Logic Function | AND, D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 8mA 8mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 8.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Output Lines | 1 |
| fmax-Min | 80 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 8.65mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74AHCT74D,118 Overview
It is embeded in 14-SOIC (0.154, 3.90mm Width) case. It is included in the package Tape & Reel (TR). There is a Differentialoutput configured with it. The trigger configured with it uses Positive Edge. Surface Mountmounts this electrical part. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. The operating temperature is -40°C~125°C TA. A flip flop of this type is classified as a D-Type. This type of FPGA is a part of the 74AHCT series. You should not exceed 140MHzin the output frequency of the device. The number of terminations is 14. The object belongs to the 74AHCT74 family. Power is provided by a 5V supply. There is 3pF input capacitance for this T flip flop. In this case, the D flip flop belongs to the AHCT/VHCTfamily. There is an electronic part mounted in the way of Surface Mount. The 14pins are designed into the board. A Positive Edgeclock edge trigger is used in this device. To achieve this superior flexibility, 2 circuits are used. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. There are no output lines on the JK flip flop. Quiescent current is consumed by the D latch in the amount of 2μA.
74AHCT74D,118 Features
Tape & Reel (TR) package
74AHCT series
14 pins
74AHCT74D,118 Applications
There are a lot of Nexperia USA Inc. 74AHCT74D,118 Flip Flops applications.
- Patented noise
- Computers
- Synchronous counter
- Digital electronics systems
- Modulo – n – counter
- Communications
- Data transfer
- Data storage
- Reduced system switching noise
- Automotive
