74AHCT74PW-Q100J
| Parameters | |
|---|---|
| Number of Terminations | 14 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74AHCT74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Clock Frequency | 140MHz |
| Propagation Delay | 14.5 ns |
| Quiescent Current | 2μA |
| Family | AHCT/VHCT/VT |
| Current - Output High, Low | 8mA 8mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 8.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| fmax-Min | 80 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Series | 74AHCT |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
74AHCT74PW-Q100J Overview
The flip flop is packaged in a case of 14-TSSOP (0.173, 4.40mm Width). D flip flop is included in the Tape & Reel (TR)package. This output is configured with Differential. This trigger uses the value Positive Edge. The electronic part is mounted in the way of Surface Mount. A supply voltage of 4.5V~5.5V is required for operation. -40°C~125°C TAis the operating temperature. This D latch has the type D-Type. In this case, it is a type of FPGA belonging to the 74AHCT series. Its output frequency should not exceed 140MHz. In total, it contains 2 elements. There have been 14 terminations. D latch belongs to the 74AHCT74 family. It is powered by a voltage of 5V . A JK flip flop with a 3pFfarad input capacitance is used here. It is a member of the AHCT/VHCT/VTfamily of D flip flop. This electronic part is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 14. In this device, the clock edge trigger type is Positive Edge. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. It consumes a total of 2μA quiescent current at any given time.
74AHCT74PW-Q100J Features
Tape & Reel (TR) package
74AHCT series
14 pins
74AHCT74PW-Q100J Applications
There are a lot of Nexperia USA Inc. 74AHCT74PW-Q100J Flip Flops applications.
- Set-reset capability
- Latch
- Storage registers
- Count Modes
- Latch-up performance
- Bus hold
- Data Synchronizers
- Individual Asynchronous Resets
- Power down protection
- Dynamic threshold performance
