74ALVCF162834LRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 56-BSSOP (0.295, 7.50mm Width) |
| Number of Pins | 56 |
| Weight | 694.790113mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Series | 74ALVCF |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 56 |
| Subcategory | Bus Driver/Transceivers |
| Packing Method | TAPE AND REEL |
| Voltage - Supply | 2.3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.635mm |
| Base Part Number | 74ALVCF162834 |
| Pin Count | 56 |
| Number of Outputs | 18 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 3.6V |
| Power Supplies | 3.3V |
| Supply Voltage-Min (Vsup) | 2.3V |
| Number of Circuits | 18-Bit |
| Number of Ports | 2 |
| Output Current | 18mA |
| Number of Bits | 18 |
| Propagation Delay | 5.6 ns |
| Family | ALVC/VCX/A |
| Direction | Unidirectional |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Current - Output High, Low | 18mA 18mA |
| Logic Type | Universal Bus Driver, CMOS |
| Prop. Delay@Nom-Sup | 3.5 ns |
| Control Type | ENABLE LOW |
| Height Seated (Max) | 2.79mm |
| Width | 7.49mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74ALVCF162834LRG4 Overview
The package 56-BSSOP (0.295, 7.50mm Width) contains this file embedded in it. In this case, it is packaged in the same way as Tape & Reel (TR). The superior flexibility of 18-Bit circuits is achieved through their use. This electrical device is of the Universal Bus Driver, CMOS logic type. I have mounted this electronic part in the way of Surface Mount in this way. Operating temperatures should be higher than -40°C~85°C. High/Low output currents allow 18mA 18mA to have a maximum design flexibility. An FPGA belonging to the 74ALVCF series is a type of FPGA. The supply voltage for the machine is 2.3V~3.6V and it operates on that voltage. As it belongs to the 74ALVCF162834 family, it should be taken into consideration. The 56 termination is a practice in which a transmission line is terminated with an impedance matching device at the end of the line in order to match the characteristic impedance of the line. It is recommended that the supply voltage be kept above 2.5V for normal operation. 56 pins are included. The electronic part was designed using 18 Bits. Transmission lines can be terminated with 2 terminations by using a device that matches the characteristic impedance. As you can see from the image, this electronic component is mounted in a Surface Mount-direction. 56 pins are used in the design of this board. It is a member of the ALVC/VCX/A family of electronic devices. Upon reaching 3.6V, the supply voltage (Vsup) reaches its maximum value. It is recommended that the supply voltage (Vsup) be greater than 2.3V. The power source is 3.3V. The reliable performance of this device makes it a good choice for TAPE AND REEL. Because of 18mA's output current, it is very versatile due to its maximum design flexibility. In Bus Driver/Transceivers, there is this part. There are 18 outputs configured on it.
74ALVCF162834LRG4 Features
56-BSSOP (0.295, 7.50mm Width) package
74ALVCF series
74ALVCF162834 family
56 pin count
56 pins
3.3V power supplies
18 outputs
74ALVCF162834LRG4 Applications
There are a lot of Texas Instruments 74ALVCF162834LRG4 Universal Bus Functions applications.
- Small ground power station
- Island protection
- Troubleshooting & Judgment
- Data transfer
- Tablets
- CMOS circuitry
- Car refrigerator
- Urban rail vehicle
- MPPT function (maximum power point tracking)
- Microprocessors
