74AUP1G74DC-Q100H
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-VFSOP (0.091, 2.30mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100, 74AUP |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 0.8V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 1.1V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 3.6V |
| Number of Bits | 1 |
| Clock Frequency | 315MHz |
| Propagation Delay | 5.8 ns |
| Quiescent Current | 500nA |
| Family | AUP/ULP/V |
| Logic Function | AND, D-Type |
| Current - Output High, Low | 4mA 4mA |
| Max Propagation Delay @ V, Max CL | 5.8ns @ 3.3V, 30pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 0.6pF |
| fmax-Min | 550 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 2.3mm |
| Width | 2mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74AUP1G74DC-Q100H Overview
It is packaged in the way of 8-VFSOP (0.091, 2.30mm Width). You can find it in the Tape & Reel (TR)package. The output it is configured with uses Differential. The trigger it is configured with uses Positive Edge. There is an electronic component mounted in the way of Surface Mount. A voltage of 0.8V~3.6Vis required for its operation. Temperature is set to -40°C~125°C TA. A flip flop of this type is classified as a D-Type. The FPGA belongs to the Automotive, AEC-Q100, 74AUP series. In order for it to function properly, its output frequency should not exceed 315MHz. In total, there are 1 elements. There are 8 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The power supply voltage is 1.1V. This T flip flop has a capacitance of 0.6pF farads at the input. This D flip flop belongs to the family of AUP/ULP/V. This electronic part is mounted in the way of Surface Mount. With its 8pins, it is designed to work with most electronic flip flops. This device exhibits a clock edge trigger type of Positive Edge. This flip flop is designed with 1 Bits. 3.6Vis the maximum supply voltage (Vsup). This D latch consumes 500nA quiescent current at all.
74AUP1G74DC-Q100H Features
Tape & Reel (TR) package
Automotive, AEC-Q100, 74AUP series
8 pins
1 Bits
74AUP1G74DC-Q100H Applications
There are a lot of Nexperia USA Inc. 74AUP1G74DC-Q100H Flip Flops applications.
- ATE
- Differential Individual
- Common Clocks
- Frequency division
- Balanced Propagation Delays
- Control circuits
- Reduced system switching noise
- Latch-up performance
- Shift Registers
- Shift registers
