74F175PC
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Supplier Device Package | 16-PDIP |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74F |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 140MHz |
| Base Part Number | 74F175 |
| Function | Master Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Output Current | 20mA |
| Number of Bits | 4 |
| Clock Frequency | 140MHz |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 5 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 34mA |
| Current - Output High, Low | 1mA 20mA |
| Number of Gates | 4 |
| Number of Bits per Element | 4 |
| Max Frequency | 100MHz |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -1mA |
| Low Level Output Current | 20mA |
| Number of Input Lines | 4 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
74F175PC Overview
16-DIP (0.300, 7.62mm)is the way it is packaged. There is an embedded version in the package Tube. T flip flop uses Differentialas the output. The trigger configured with it uses Positive Edge. There is an electric part mounted in the way of Through Hole. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. The operating temperature is 0°C~70°C TA. There is D-Type type of electronic flip flop associated with this device. FPGAs belonging to the 74Fseries contain this type of chip. A frequency of 140MHzshould be the maximum output frequency. D latch consists of 1 elements. As a result, it consumes 34mA of quiescent current without being affected by external factors. The 74F175 family contains it. Through Hole mounts this electronic component. The electronic flip flop is designed with pins 16. There is a clock edge trigger type of Positive Edgeon this device. The design is based on 4bits. 4 circuits are used to achieve its superior flexibility. If high efficiency is desired, the supply voltage should be kept at 5V. It offers maximum design flexibility with its output current of 20mA. It operates with 3 output lines. Currently, there are 4 lines of input. A -1mAvalue is set for the high level output current. It is set to 20mAfor the low level output current. The operating temperature should be lower than 70°C. Ideally, the operating temperature should be greater than 0°C. It is powered by 4.5V as its minimum supply voltage. 5.5Vis the maximum supply voltage supported by it. This frequency can be achieved at 140MHz. The building block contains a total of 4 gates.
74F175PC Features
Tube package
74F series
16 pins
4 Bits
4 gates
74F175PC Applications
There are a lot of ON Semiconductor 74F175PC Flip Flops applications.
- Divide a clock signal by 2 or 4
- Shift Registers
- Storage Registers
- ESD performance
- Storage registers
- Balanced 24 mA output drivers
- Convert a momentary switch to a toggle switch
- Functionally equivalent to the MC10/100EL29
- Consumer
- Computers
