74F273SJX
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SOP |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74F |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 160MHz |
| Base Part Number | 74F273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 160MHz |
| Propagation Delay | 9 ns |
| Turn On Delay Time | 7 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 44mA |
| Current - Output High, Low | 1mA 20mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 9ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -1mA |
| Low Level Output Current | 20mA |
| Number of Input Lines | 8 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74F273SJX Overview
The item is packaged in 20-SOIC (0.209, 5.30mm Width)cases. It is included in the package Tape & Reel (TR). There is a Non-Invertedoutput configured with it. In the configuration of the trigger, Positive Edgeis used. Surface Mountmounts this electrical part. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. A temperature of 0°C~70°C TAis considered to be the operating temperature. This logic flip flop is classified as type D-Type. The 74Fseries comprises this type of FPGA. Its output frequency should not exceed 160MHz Hz. D latch consists of 1 elements. T flip flop consumes 44mA quiescent energy. The object belongs to the 74F273 family. In this case, the electronic component is mounted in the way of Surface Mount. The 20pins are designed into the board. It has a clock edge trigger type of Positive Edge. It is designed with a number of bits of 8. The superior flexibility is achieved through the use of 8 circuits. The supply voltage should be maintained at 5V for high efficiency. To operate, the chip has a total of 3 output lines. It is reported that there are 8 input lines. A -1mAvalue is set for the high level output current. There is no low level output current set at 20mA. It is recommended that the operating temperature be below 70°C. Ideally, the operating temperature should be higher than 0°C. The minimal supply voltage is 4.5V. 5.5Vis its maximum supply voltage. The frequency can be set to 160MHz.
74F273SJX Features
Tape & Reel (TR) package
74F series
20 pins
8 Bits
74F273SJX Applications
There are a lot of ON Semiconductor 74F273SJX Flip Flops applications.
- Balanced Propagation Delays
- Differential Individual
- Test & Measurement
- Memory
- 2 – Bit synchronous counter
- Safety Clamp
- Counters
- CMOS Process
- Shift Registers
- Power down protection
