74FCT162374ATPACT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 48-TFSOP (0.240, 6.10mm Width) |
| Number of Pins | 48 |
| Weight | 223.195796mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74FCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 48 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | 74FCT162374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 1 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 16 |
| Propagation Delay | 6.5 ns |
| Quiescent Current | 5μA |
| Turn On Delay Time | 2 ns |
| Family | FCT |
| Current - Quiescent (Iq) | 500μA |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Current - Output High, Low | 24mA 24mA |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.5mA |
| Number of Output Lines | 8 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 12.5mm |
| Width | 6.1mm |
| Thickness | 1.15mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74FCT162374ATPACT Overview
It is embeded in 48-TFSOP (0.240, 6.10mm Width) case. There is an embedded version in the package Tape & Reel (TR). T flip flop uses Tri-State, Non-Invertedas the output. This trigger uses the value Positive Edge. There is an electronic component mounted in the way of Surface Mount. The JK flip flop operates at 4.5V~5.5Vvolts. In this case, the operating temperature is -40°C~85°C TA. This logic flip flop is classified as type D-Type. In terms of FPGAs, it belongs to the 74FCT series. A total of 2elements are present in it. There is 500μA quiescent consumption. In 48terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. This D latch belongs to the family of 74FCT162374. The power supply voltage is 5V. A JK flip flop with a 4.5pFfarad input capacitance is used here. In terms of electronic devices, this device belongs to the FCTfamily of devices. A part of the electronic system is mounted in the way of Surface Mount. There are 48pins on it. It has a clock edge trigger type of Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. The design is based on 16bits. The superior flexibility is achieved through the use of 1 circuits. A reliable performance of this D flip flop makes it well suited for use in TR. It operates from 5V power supplies. The flip flop has 2ports embedded within it. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. The 24mA output current allows it to be designed with the greatest amount of flexibility. In order for the chip to function, it has 8output lines. There is a consumption of 5μAof quiescent current from it.
74FCT162374ATPACT Features
Tape & Reel (TR) package
74FCT series
48 pins
16 Bits
5V power supplies
74FCT162374ATPACT Applications
There are a lot of Texas Instruments 74FCT162374ATPACT Flip Flops applications.
- Computers
- Count Modes
- Frequency division
- ESD protection
- Shift registers
- Bus hold
- Control circuits
- Communications
- ATE
- Safety Clamp
