74FCT162374ATPAG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 48 |
| Weight | 420.990418mg |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 48 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 48 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 16 |
| Propagation Delay | 6.5 ns |
| Quiescent Current | 500μA |
| Turn On Delay Time | 6.5 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 8 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 3.5pF |
| Height | 1mm |
| Length | 12.5mm |
| Width | 6.1mm |
| Thickness | 1mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT162374ATPAG Overview
In the form of TSSOP, it has been packaged. D latch consists of 2 elements. It has been determined that there have been 48 terminations. The power source is powered by 5V. Devices in the FCTfamily are electronic devices. A part of the electronic system is mounted in the way of Surface Mount. Basically, it is designed with a set of 48 pins. In this device, the clock edge trigger type is Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. The flip flop is designed with 16bits. An electrical current of 5V volts is applied to it. A D flip flop with 2embedded ports is available. For high efficiency, the supply voltage should be kept at 5V. It consumes 500μA current. A high level output current of -24mAis set. Low level output current is set to 24mA. There should be a temperature below 85°Cduring operation. In order for the system to operate properly, the temperature should be higher than -40°C. The system operates with a minimum supply voltage of 4.5V. There is a maximum voltage support of 5.5V. There is a logic IC BUS DRIVER used in the D flip flop. It is equipped with 2 Functions . It has 48 pins.
74FCT162374ATPAG Features
48 pins
16 Bits
5V power supplies
2 Functions
48 pin count
74FCT162374ATPAG Applications
There are a lot of Integrated Device Technology (IDT) 74FCT162374ATPAG Flip Flops applications.
- Patented noise
- Computers
- Communications
- QML qualified product
- Cold spare funcion
- Data Synchronizers
- Set-reset capability
- Supports Live Insertion
- Buffer registers
- Synchronous counter
