74FCT162374ATPVCG4
| Parameters | |
|---|---|
| Contact Plating | Gold |
| Mount | Surface Mount |
| Package / Case | SSOP |
| Number of Pins | 48 |
| Weight | 600.301152mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 48 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Frequency | 10MHz |
| Pin Count | 48 |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 24mA |
| Number of Bits | 16 |
| Propagation Delay | 6.5 ns |
| Quiescent Current | 5μA |
| Turn On Delay Time | 2 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Logic IC Type | BUS DRIVER |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.59mm |
| Length | 15.88mm |
| Width | 7.49mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT162374ATPVCG4 Overview
The item is packaged in SSOPcases. D latch consists of 2 elements. A total of 48terminations have been recorded. It is powered by a voltage of 5V . The electronic device belongs to the FCTfamily. A part of the electronic system is mounted in the way of Surface Mount. A total of 48pins are provided on this board. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The part is included in FF/Latches. 16bits are used in its design. Despite its superior flexibility, it relies on 4 circuits to achieve it. In light of its reliable performance, this T flip flop is well suited for TUBE. A total of 5V power supplies are needed to run it. There are 2 ports embedded in the flip flops. The supply voltage should be maintained at 5V for high efficiency. It is reported that there are 8 input lines. In terms of quiescent current, it consumes 5μA . -24mA is set as the high level output current. It is set to 24mAfor low level output current. Operating temperatures should be lower than 85°C. Operating temperatures should be above -40°C. The RS flip flop is designed to operate with a minimal supply voltage of 4.5VV. 5.5Vis its maximum supply voltage. The frequency that can be achieved is 10MHz. It uses BUS DRIVERas its logic IC. The T flip flop is equipped with 2functions . It is equipped with 48 pin count. It features maximum design flexibility due to the 24mA output current.
74FCT162374ATPVCG4 Features
48 pins
16 Bits
5V power supplies
2 Functions
48 pin count
74FCT162374ATPVCG4 Applications
There are a lot of Texas Instruments 74FCT162374ATPVCG4 Flip Flops applications.
- Cold spare funcion
- Power down protection
- Data Synchronizers
- Divide a clock signal by 2 or 4
- Balanced Propagation Delays
- Pattern generators
- Memory
- Buffered Clock
- Parallel data storage
- ESCC
