74FCT162374CTPAG8
| Parameters | |
|---|---|
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 48 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 16 |
| Propagation Delay | 5.2 ns |
| Quiescent Current | 500μA |
| Turn On Delay Time | 5.5 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 8 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 3.5pF |
| Length | 12.5mm |
| Width | 6.1mm |
| Thickness | 1mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 48 |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 48 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
74FCT162374CTPAG8 Overview
The flip flop is packaged in a case of TSSOP. It is contained within the Tape & Reel (TR)package. A total of 2 elements are present. Terminations are 48. The power source is powered by 5V. An electronic device belonging to the family FCTcan be found here. There is an electronic part mounted in the way of Surface Mount. This board is designed with 48pins on it. It has a clock edge trigger type of Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. An electronic part with 16bits has been designed. In view of its reliability, this D flip flop is a good fit for TAPE AND REEL. The D latch operates on 5V volts. This flip flop has a total of 2ports. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. It consumes a total of 500μA quiescent current at any given time. -24mA is set as the high level output current. 24mA is the low level output current. There should be a temperature below 85°Cduring operation. Operating temperatures should be above -40°C. The system operates with a minimum supply voltage of 4.5V. There is a maximum supply voltage of 5.5V. The logic IC it uses is BUS DRIVER. There are 2 functions available on the JK flip flop. With 48 pins, it is equipped with a low power consumption.
74FCT162374CTPAG8 Features
Tape & Reel (TR) package
48 pins
16 Bits
5V power supplies
2 Functions
48 pin count
74FCT162374CTPAG8 Applications
There are a lot of Integrated Device Technology (IDT) 74FCT162374CTPAG8 Flip Flops applications.
- Individual Asynchronous Resets
- QML qualified product
- Computers
- Buffer registers
- High Performance Logic for test systems
- Common Clocks
- Event Detectors
- Circuit Design
- ATE
- ESD protection
