74FCT162374ETPAG8
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 48 |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 48 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 48 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 16 |
| Propagation Delay | 3.7 ns |
| Quiescent Current | 500μA |
| Turn On Delay Time | 4.4 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 8 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 3.5pF |
| Length | 12.5mm |
| Width | 6.1mm |
| Thickness | 1mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT162374ETPAG8 Overview
The flip flop is packaged in TSSOP. The element count is 2 . Currently, there are 48 terminations. It is powered by a voltage of 5V . A device of this type belongs to the family of FCT. In this case, the electronic component is mounted in the way of Surface Mount. As you can see from the design, it has pins with 48. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This device has the base part number FF/Latches. This flip flop is designed with 16 Bits. This D flip flop is well suited for TAPE AND REEL based on its reliable performance. The D latch runs on a voltage of 5V volts. The flip flop contains 2ports. For high efficiency, the supply voltage should be kept at 5V. It consumes 500μA current. In this case, the high level output current is set to -24mA. In the low level output current setting, 24mAis used. It is recommended that the operating temperature be below 85°C. In order for the system to operate properly, the temperature should be higher than -40°C. It operates with the minimal supply voltage of 4.5V. The maximum supply voltage supported by the flip flop is 5.5V. There is a logic IC BUS DRIVER used in the D flip flop. There are 2 functions associated with the JK flip flop. It has 48 pins.
74FCT162374ETPAG8 Features
48 pins
16 Bits
5V power supplies
2 Functions
48 pin count
74FCT162374ETPAG8 Applications
There are a lot of Integrated Device Technology (IDT) 74FCT162374ETPAG8 Flip Flops applications.
- Asynchronous counter
- Set-reset capability
- Divide a clock signal by 2 or 4
- Reduced system switching noise
- Single Down Count-Control Line
- Automotive
- Patented noise
- Registers
- ATE
- ESD protection
