74FCT162823ATPVG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SSOP |
| Number of Pins | 56 |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 56 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | WITH CLEAR AND CLOCK ENABLE |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 56 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 18 |
| Propagation Delay | 20 ns |
| Quiescent Current | 500μA |
| Turn On Delay Time | 23 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 9 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 3.5pF |
| Length | 18.4mm |
| Width | 7.5mm |
| Thickness | 2.3mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT162823ATPVG Overview
It is embeded in SSOP case. A total of 2elements are present in it. There are 56 terminations,Power is supplied from a voltage of 5V volts. FCTis the family of this D flip flop. The electronic part is mounted in the way of Surface Mount. The 56pins are designed into the board. There is a clock edge trigger type of Positive Edgeon this device. It is included in FF/Latches. Flip flops designed with 18bits are used in this part. There are 5V power supplies attached to it. This D flip flop is equipped with 0 ports. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. It consumes 500μA current. WITH CLEAR AND CLOCK ENABLEis also one of its characteristics. -24mAis the output current at high level. Low level output current is set to 24mA. A temperature below 85°Cis recommended for operation. The operating temperature should be higher than -40°C. A minimum supply voltage of 4.5V is required for these RS flip flops to operate. 5.5Vis the maximum supply voltage it supports. It uses BUS DRIVERas its logic IC. A total of 2 functions are provided by this T flip flop. The D latch is equipped with 56 pins.
74FCT162823ATPVG Features
56 pins
18 Bits
5V power supplies
2 Functions
56 pin count
74FCT162823ATPVG Applications
There are a lot of Integrated Device Technology (IDT) 74FCT162823ATPVG Flip Flops applications.
- Matched Rise and Fall
- Latch-up performance
- Data Synchronizers
- CMOS Process
- Single Up Count-Control Line
- Shift Registers
- Data transfer
- Digital electronics systems
- Computers
- High Performance Logic for test systems
