74FCT162823CTPAG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | TFSOP |
| Number of Pins | 56 |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 56 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | WITH CLEAR AND CLOCK ENABLE |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 56 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 18 |
| Propagation Delay | 8 ns |
| Quiescent Current | 500μA |
| Turn On Delay Time | 12.5 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 9 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 3.5pF |
| Length | 14mm |
| Width | 6.1mm |
| Thickness | 1mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT162823CTPAG Overview
It is embeded in TFSOP case. In total, it contains 2 elements. There are 56 terminations,A voltage of 5V is used to power it. The electronic device belongs to the FCTfamily. Electronic part Surface Mountis mounted in the way. There are 56pins on it. A Positive Edgeclock edge trigger is used in this device. It is part of the FF/Latchesbase part number family. There are 18bits in its design. Considering its reliability, this T flip flop is well suited for TAPE AND REEL. There are 5V power supplies attached to it. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. In order to ensure high efficiency, the supply voltage should remain at 5V. It consumes 500μA of quiescent current without being affected by external factors. In addition, WITH CLEAR AND CLOCK ENABLEis a characteristic of it. A -24mAvalue is set for the high level output current. In the low level output current setting, the current is set to 24mA. Ideally, the operating temperature should be below 85°C. It is recommended that the operating temperature is higher than -40°C. Normally, it operates with a voltage of 4.5VV as its minimum supply voltage. There is a maximum voltage support of 5.5V. There is a logic IC BUS DRIVER used in the D flip flop. As a result, it is equipped with 2 functions . It has 56 pins.
74FCT162823CTPAG Features
56 pins
18 Bits
5V power supplies
2 Functions
56 pin count
74FCT162823CTPAG Applications
There are a lot of Integrated Device Technology (IDT) 74FCT162823CTPAG Flip Flops applications.
- Control circuits
- Count Modes
- Shift Registers
- Common Clocks
- Data transfer
- Storage registers
- Safety Clamp
- Matched Rise and Fall
- Latch
- Registers
