74FCT162823CTPAG8
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 56 |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 56 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | WITH CLEAR AND CLOCK ENABLE |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 56 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 18 |
| Propagation Delay | 8 ns |
| Quiescent Current | 500μA |
| Turn On Delay Time | 12.5 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 9 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 3.5pF |
| Length | 14mm |
| Width | 6.1mm |
| Thickness | 1mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT162823CTPAG8 Overview
The flip flop is packaged in a case of TSSOP. A total of 2elements are contained within it. The number of terminations is 56. An input voltage of 5Vpowers the D latch. It is a member of the FCTfamily of D flip flop. There is an electronic part that is mounted in the way of Surface Mount. With its 56pins, it is designed to work with most electronic flip flops. This device has the clock edge trigger type of Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. There are 18bits in this flip flop. This D flip flop is well suited for TAPE AND REEL based on its reliable performance. It runs on 5Vvolts of power. The D flip flop is embedded with 2ports. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. There is a consumption of 500μAof quiescent current from it. There is also a characteristic of WITH CLEAR AND CLOCK ENABLE. -24mAis the output current at high level. 24mA is the low level output current. It is recommended that the operating temperature be below 85°C. Ideally, the operating temperature should be higher than -40°C. The minimum voltage required for operation is 4.5V. It supports the maximal supply voltage of 5.5V. There is a logic IC BUS DRIVER used in the D flip flop. Currently, it is equipped with 2 functions . It is equipped with 56 pin count.
74FCT162823CTPAG8 Features
56 pins
18 Bits
5V power supplies
2 Functions
56 pin count
74FCT162823CTPAG8 Applications
There are a lot of Integrated Device Technology (IDT) 74FCT162823CTPAG8 Flip Flops applications.
- Supports Live Insertion
- Single Up Count-Control Line
- ATE
- Memory
- Frequency Dividers
- Dynamic threshold performance
- Circuit Design
- Reduced system switching noise
- Balanced Propagation Delays
- 2 – Bit synchronous counter
