74FCT162823CTPVG8
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SSOP |
| Number of Pins | 56 |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 56 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | WITH CLEAR AND CLOCK ENABLE |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 56 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 18 |
| Propagation Delay | 8 ns |
| Quiescent Current | 500μA |
| Turn On Delay Time | 12.5 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 9 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 3.5pF |
| Length | 18.4mm |
| Width | 7.5mm |
| Thickness | 2.3mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT162823CTPVG8 Overview
It is packaged in the way of SSOP. The list contains 2 elements. The number of terminations is 56. The power source is powered by 5V. This D flip flop belongs to the family of FCT. It is mounted in the way of Surface Mount. This board is designed with 56pins on it. This device has the clock edge trigger type of Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. An electronic part with 18bits has been designed. A reliable performance of this D flip flop makes it well suited for use in TAPE AND REEL. It operates from 5V power supplies. The flip flop contains 2ports. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. 500μAquiescent current consumed. As an additional reference, you may refer to electronic flip flop WITH CLEAR AND CLOCK ENABLE. -24mAis the output current at high level. It is set to 24mAfor the low level output current. The operating temperature should be lower than 85°C. A temperature above -40°Cshould be used for the operation. It operates with the minimal supply voltage of 4.5V. It is capable of supporting a maximum supply voltage of 5.5V. It uses BUS DRIVERas its logic IC. Currently, it is equipped with 2 functions . The JK flip flop has a pin count of 56.
74FCT162823CTPVG8 Features
56 pins
18 Bits
5V power supplies
2 Functions
56 pin count
74FCT162823CTPVG8 Applications
There are a lot of Integrated Device Technology (IDT) 74FCT162823CTPVG8 Flip Flops applications.
- Supports Live Insertion
- Bus hold
- Divide a clock signal by 2 or 4
- Test & Measurement
- Digital electronics systems
- Synchronous counter
- Patented noise
- ATE
- Bounce elimination switch
- Single Down Count-Control Line
