74FCT16374ATPAG8
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 48 |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 48 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | POWER OFF DISABLE O/PS; IOH MAX DURATION < 1S; MAX OUTPUT SKEW = 0.5NS |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 48 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 16 |
| Propagation Delay | 6.5 ns |
| Quiescent Current | 500μA |
| Turn On Delay Time | 6.5 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.064 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -32mA |
| Low Level Output Current | 32mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 3.5pF |
| Length | 12.5mm |
| Width | 6.1mm |
| Thickness | 1mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT16374ATPAG8 Overview
The flip flop is packaged in a case of TSSOP. In total, it contains 2 elements. In 48terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. A voltage of 5V provides power to the D latch. A device of this type belongs to the family of FCT. There is an electronic part that is mounted in the way of Surface Mount. The 48pins are designed into the board. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. It is part of the FF/Latchesbase part number family. The design is based on 16bits. As a result of its reliability, this D flip flop is ideally suited for TAPE AND REEL. A power supply of 5Vis required to operate it. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. Optimal efficiency requires a supply voltage of 5V. As a result, it consumes 500μA of quiescent current without being affected by external factors. POWER OFF DISABLE O/PS; IOH MAX DURATION < 1S; MAX OUTPUT SKEW = 0.5NSis also one of its characteristics. The high level output current is set to -32mA. 32mAis set as the low level output current. The operating temperature should be lower than 85°C. It is recommended that the operating temperature is higher than -40°C. Normally, it operates with a voltage of 4.5VV as its minimum supply voltage. 5.5Vis the maximum supply voltage it supports. It adopts a logic IC of type BUS DRIVER. There are 2 functions available on this T flip flop. With 48 pins, it is equipped with a low power consumption.
74FCT16374ATPAG8 Features
48 pins
16 Bits
5V power supplies
2 Functions
48 pin count
74FCT16374ATPAG8 Applications
There are a lot of Integrated Device Technology (IDT) 74FCT16374ATPAG8 Flip Flops applications.
- Event Detectors
- Frequency division
- Pattern generators
- Communications
- Reduced system switching noise
- Digital electronics systems
- Storage registers
- Convert a momentary switch to a toggle switch
- Functionally equivalent to the MC10/100EL29
- QML qualified product
