74FCT16374ETPAG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 48 |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 48 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | POWER OFF DISABLE O/PS; IOH MAX DURATION < 1S; MAX OUTPUT SKEW = 0.5NS |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 48 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 16 |
| Propagation Delay | 3.7 ns |
| Quiescent Current | 500μA |
| Turn On Delay Time | 4.4 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.064 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -32mA |
| Low Level Output Current | 32mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 3.5pF |
| Length | 12.5mm |
| Width | 6.1mm |
| Thickness | 1mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT16374ETPAG Overview
It is embeded in TSSOP case. D latch consists of 2 elements. It has been determined that there have been 48 terminations. A voltage of 5V provides power to the D latch. An electronic device belonging to the family FCTcan be found here. There is an electronic part mounted in the way of Surface Mount. The electronic flip flop is designed with pins 48. A Positive Edgeclock edge trigger is used in this device. The RS flip flops belongs to FF/Latches base part number. An electronic part designed with 16bits is used in this application. It runs on 5Vvolts of power. This D flip flop is equipped with 0 ports. If high efficiency is desired, the supply voltage should be kept at 5V. In terms of quiescent current, it consumes 500μA . POWER OFF DISABLE O/PS; IOH MAX DURATION < 1S; MAX OUTPUT SKEW = 0.5NSis also one of its characteristics. A high level output current of -32mAis set. 32mA is the low level output current. There should be a temperature below 85°Cduring operation. A temperature above -40°Cshould be used for the operation. Despite its minimal supply voltage of 4.5V, it is capable of operating. It supports a maximum supply voltage of 5.5V volts. The logic IC it adopts is BUS DRIVER. The T flip flop is equipped with 2functions . It is equipped with 48 pins.
74FCT16374ETPAG Features
48 pins
16 Bits
5V power supplies
2 Functions
48 pin count
74FCT16374ETPAG Applications
There are a lot of Integrated Device Technology (IDT) 74FCT16374ETPAG Flip Flops applications.
- Latch
- Automotive
- Set-reset capability
- Pattern generators
- Count Modes
- Event Detectors
- Single Down Count-Control Line
- Test & Measurement
- Latch-up performance
- Memory
