74FCT16500CTPACTG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 56-TFSOP (0.240, 6.10mm Width) |
| Number of Pins | 56 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Series | 74FCT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 56 |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74FCT16500 |
| Pin Count | 56 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 18-Bit |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Ports | 2 |
| Number of Bits | 18 |
| Propagation Delay | 5.3 ns |
| Family | FCT |
| Logic Function | Transceiver |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 23mA 64mA |
| Logic Type | Universal Bus Transceiver |
| Max I(ol) | 0.064 A |
| Prop. Delay@Nom-Sup | 4.6 ns |
| Trigger Type | NEGATIVE EDGE |
| Control Type | INDEPENDENT CONTROL |
| Count Direction | BIDIRECTIONAL |
| Translation | N/A |
| Height Seated (Max) | 1.2mm |
| Length | 14mm |
| Width | 6.1mm |
| RoHS Status | ROHS3 Compliant |
74FCT16500CTPACTG4 Overview
It is embedded in the 56-TFSOP (0.240, 6.10mm Width) package. I have packaged it in a way that is similar to Tape & Reel (TR)'s. It achieves superior flexibility through 18-Bit circuits. Logic type Universal Bus Transceiver is used on this electrical device. It is mounted in the way of Surface Mount so that this electronic part can be seen. -40°C~85°C should be higher than the operating temperature. The high/low output current of 23mA 64mA enables maximum design flexibility. An FPGA belonging to the 74FCT series is a type of FPGA. The 74FCT16500 family includes it. It can be said that there is a technique of terminating transmission lines that uses a device that matches the characteristics of the line impedance, called 56 terminations. In order to maintain normal operation of the device, the supply voltage should remain above 5V. 56 pins are included. 18 Bits were used in the design of this electronic part. An example of this is through the use of 2 terminations, where a particular device is used to end a transmission line with an impedance matching device, fitted with its characteristic impedance. In this case, the electronic part will be mounted in the Surface Mount-direction. 56 pins are used in the design. This electronic device belongs to the family of FCT. Power is provided by 5V power supplies. It uses NEGATIVE EDGE for its trigger. Based on its reliable performance, this device is well suited for TAPE AND REEL. During operation, a minimum supply voltage of 4.5V is used. The maximum supply voltage of 5.5V is supported.
74FCT16500CTPACTG4 Features
56-TFSOP (0.240, 6.10mm Width) package
74FCT series
74FCT16500 family
56 pin count
56 pins
5V power supplies
74FCT16500CTPACTG4 Applications
There are a lot of Texas Instruments 74FCT16500CTPACTG4 Universal Bus Functions applications.
- Audio
- Solar street light
- Photovoltaic system
- Calculator
- Illumination
- automatic temperature control circuits
- Fan
- Overcurrent/Short circuit protection
- Massager
- Digital watch
