74FCT374ATQG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | QSOP |
| Number of Pins | 20 |
| Packaging | Rail/Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 6.5 ns |
| Quiescent Current | 1mA |
| Turn On Delay Time | 6.5 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| High Level Output Current | -15mA |
| Low Level Output Current | 48mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 6pF |
| Length | 8.7mm |
| Width | 3.8mm |
| Thickness | 1.47mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT374ATQG Overview
It is packaged in the way of QSOP. D flip flop is included in the Rail/Tubepackage. A total of 1elements are present in it. The number of terminations is 20. A voltage of 5V is used to power it. Electronic devices of this type belong to the FCTfamily. There is an electronic part that is mounted in the way of Surface Mount. This board is designed with 20pins on it. This device has Positive Edgeas its clock edge trigger type. There is a FF/Latchesbase part number assigned to the RS flip flops. 8bits are used in its design. It runs on 5Vvolts of power. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. In order to ensure high efficiency, the supply voltage should remain at 5V. There is a consumption of 1mAof quiescent current from it. The high level output current is set to -15mA. 48mAis set as the low level output current. A temperature below 85°Cis recommended for operation. A temperature above -40°Cshould be used for the operation. The minimal supply voltage is 4.75V. 5.25Vis the maximum supply voltage supported by it. This logic IC is BUS DRIVER. It has 1 functions. The D latch is equipped with 20 pins.
74FCT374ATQG Features
Rail/Tube package
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
74FCT374ATQG Applications
There are a lot of Integrated Device Technology (IDT) 74FCT374ATQG Flip Flops applications.
- Divide a clock signal by 2 or 4
- Memory
- Frequency Divider circuits
- ESD protection
- Communications
- Pattern generators
- Set-reset capability
- Load Control
- Event Detectors
- Registers
