74FCT374ATSOG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 6.5 ns |
| Quiescent Current | 1mA |
| Turn On Delay Time | 6.5 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| High Level Output Current | -15mA |
| Low Level Output Current | 48mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 6pF |
| Length | 12.8mm |
| Width | 7.6mm |
| Thickness | 2.34mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT374ATSOG Overview
The item is packaged in SOICcases. There are 1 elements in it. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. The power supply voltage is 5V. This D flip flop belongs to the family of FCT. This electronic part is mounted in the way of Surface Mount. With its 20pins, it is designed to work with most electronic flip flops. The clock edge trigger type for this device is Positive Edge. It is part of the FF/Latchesbase part number family. This flip flop is designed with 8 Bits. As a result of its reliability, this D flip flop is ideally suited for TUBE. A power supply of 5Vis required to operate it. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. If high efficiency is desired, the supply voltage should be kept at 5V. It consumes 1mA of quiescent current without being affected by external factors. The high level output current is set to -15mA. The low level output current is set to 48mA. If the operating temperature is lower than 85°C, it is recommended. Ideally, the operating temperature should be greater than -40°C. The minimal supply voltage is 4.75V. 5.25Vis its maximum supply voltage. The logic IC it uses is BUS DRIVER. As a result, it is equipped with 1 functions . It is equipped with 20 pins.
74FCT374ATSOG Features
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
74FCT374ATSOG Applications
There are a lot of Integrated Device Technology (IDT) 74FCT374ATSOG Flip Flops applications.
- Test & Measurement
- Frequency Divider circuits
- ESD protection
- QML qualified product
- Synchronous counter
- Power down protection
- Consumer
- Circuit Design
- Single Down Count-Control Line
- Digital electronics systems
