74FCT377CTSOG
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | WITH HOLD MODE |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Propagation Delay | 5.2 ns |
| Quiescent Current | 1mA |
| Turn On Delay Time | 5.2 ns |
| Family | FCT |
| Logic Function | AND, D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | D FLIP-FLOP |
| High Level Output Current | -15mA |
| Low Level Output Current | 12mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 6pF |
| Length | 12.8mm |
| Width | 7.6mm |
| Thickness | 2.34mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT377CTSOG Overview
SOICis the way it is packaged. In total, it contains 1 elements. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. A voltage of 5V provides power to the D latch. An electronic device belonging to the family FCTcan be found here. The electronic part is mounted in the way of Surface Mount. Basically, it is designed with a set of 20 pins. Its clock edge trigger type is Positive Edge. It is included in FF/Latches. It is designed with a number of bits of 8. The D latch operates on 5V volts. The supply voltage should be maintained at 5V for high efficiency. Despite external influences, it consumes 1mAof quiescent current. Additionally, you may refer to the D latch's additional WITH HOLD MODE. It is set to -15mAfor the high level output current. There is no low level output current set at 12mA. Ideally, the operating temperature should be lower than 85°C. Ideally, the operating temperature should be greater than -40°C. Despite its minimal supply voltage of 4.75V, it is capable of operating. It is capable of supporting a maximum supply voltage of 5.25V. It adopts a logic IC of type D FLIP-FLOP. It is equipped with 1 Functions . 20pins are available on this JK flip flop.
74FCT377CTSOG Features
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
74FCT377CTSOG Applications
There are a lot of Integrated Device Technology (IDT) 74FCT377CTSOG Flip Flops applications.
- Safety Clamp
- Single Down Count-Control Line
- ATE
- Data storage
- Bus hold
- Data transfer
- Reduced system switching noise
- Buffered Clock
- Single Up Count-Control Line
- Differential Individual
