74FCT574ATQG8
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | QSOP |
| Number of Pins | 20 |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 6.5 ns |
| Quiescent Current | 1mA |
| Turn On Delay Time | 6.5 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| High Level Output Current | -15mA |
| Low Level Output Current | 48mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 6pF |
| Length | 8.7mm |
| Width | 3.8mm |
| Thickness | 1.47mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT574ATQG8 Overview
The package is in the form of QSOP. D latch consists of 1 elements. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. A voltage of 5V is used as the power supply for this D latch. It is a member of the FCTfamily of D flip flop. Electronic part Surface Mountis mounted in the way. 20pins are included in its design. In this device, the clock edge trigger type is Positive Edge. This part is included in FF/Latches. There are 8bits in its design. Considering the reliability of this T flip flop, it is well suited for TAPE AND REEL. The system runs on a power supply of 5V watts. A total of 2ports are embedded in the D flip flop. The supply voltage should be maintained at 5V for high efficiency. This D latch consumes 1mA quiescent current at all. As an additional reference, you may refer to electronic flip flop BROADSIDE VERSION OF 374. The high level output current is set to -15mA. In the low level output current setting, the current is set to 48mA. If the operating temperature is lower than 85°C, it is recommended. Ideally, the operating temperature should be higher than -40°C. The system operates with a minimum supply voltage of 4.75V. In this case, it supports a maximum supply voltage of 5.25V. It adopts a logic IC of type BUS DRIVER. The T flip flop is equipped with 1functions . It is equipped with 20 pin count.
74FCT574ATQG8 Features
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
74FCT574ATQG8 Applications
There are a lot of Integrated Device Technology (IDT) 74FCT574ATQG8 Flip Flops applications.
- Functionally equivalent to the MC10/100EL29
- Memory
- Supports Live Insertion
- EMI reduction circuitry
- Shift registers
- ESD protection
- ATE
- Shift Registers
- Single Down Count-Control Line
- Parallel data storage
