74FCT574CTQG8
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SSOP |
| Number of Pins | 20 |
| Weight | 241.197743mg |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 5.2 ns |
| Quiescent Current | 1mA |
| Turn On Delay Time | 5.5 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| High Level Output Current | -15mA |
| Low Level Output Current | 15mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 6pF |
| Height | 1.47mm |
| Length | 8.7mm |
| Width | 3.8mm |
| Thickness | 1.47mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT574CTQG8 Overview
As a result, it is packaged as SSOP. The element count is 1 . In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. The power source is powered by 5V. A device of this type belongs to the family of FCT. A part of the electronic system is mounted in the way of Surface Mount. Basically, it is designed with a set of 20 pins. This device has the clock edge trigger type of Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. It is designed with a number of bits of 8. As a result of its reliable performance, this T flip flop is suitable for TAPE AND REEL. A power supply of 5Vis required to operate it. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The supply voltage should be maintained at 5V for high efficiency. It consumes 1mA current. Additionally, you may refer to the additional BROADSIDE VERSION OF 374 of the electronic flip flop. In this case, the high level output current is set to -15mA. It is set to 15mAfor the low level output current. Ideally, the operating temperature should be lower than 85°C. It is recommended that the operating temperature is higher than -40°C. It operates with the minimal supply voltage of 4.75V. There is a maximum voltage support of 5.25V. BUS DRIVERis used as the logic IC in this D flip flop. A total of 1 functions are provided by this T flip flop. There are 20 pins on the D latch.
74FCT574CTQG8 Features
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
74FCT574CTQG8 Applications
There are a lot of Integrated Device Technology (IDT) 74FCT574CTQG8 Flip Flops applications.
- Patented noise
- ATE
- Cold spare funcion
- CMOS Process
- Load Control
- Synchronous counter
- Test & Measurement
- Supports Live Insertion
- Control circuits
- Counters
