74HC107PW,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | JK Type |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC107 |
| Function | Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Voltage | 6V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 85MHz |
| Propagation Delay | 16 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | Flip-Flop, JK-Type |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 27ns @ 6V, 50pF |
| Trigger Type | Negative Edge |
| Input Capacitance | 3.5pF |
| fmax-Min | 60 MHz |
| Clock Edge Trigger Type | Negative Edge |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HC107PW,118 Overview
The item is packaged in 14-TSSOP (0.173, 4.40mm Width)cases. The Tape & Reel (TR)package contains it. This output is configured with Differential. In the configuration of the trigger, Negative Edgeis used. There is an electrical part that is mounted in the way of Surface Mount. A 2V~6Vsupply voltage is required for it to operate. In the operating environment, the temperature is -40°C~125°C TA. It is an electronic flip flop with the type JK Type. In FPGA terms, D flip flop is a type of 74HCseries FPGA. This D flip flop should not have a frequency greater than 85MHz. A total of 14 terminations have been made. The 74HC107family includes it. The D flip flop is powered by a voltage of 5V . Input capacitance of this device is 3.5pF farads. It belongs to the family of electronic devices known as HC/UH. There is an electronic part mounted in the way of Surface Mount. With its 14pins, it is designed to work with most electronic flip flops. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Negative Edge. The superior flexibility of this product is achieved by using 2 circuits. For high efficiency, the supply voltage should be kept at 5V. It consumes a total of 4μA quiescent current at any given time.
74HC107PW,118 Features
Tape & Reel (TR) package
74HC series
14 pins
74HC107PW,118 Applications
There are a lot of Nexperia USA Inc. 74HC107PW,118 Flip Flops applications.
- 2 – Bit synchronous counter
- Reduced system switching noise
- Power down protection
- Counters
- Clock pulse
- Data transfer
- Dynamic threshold performance
- Latch-up performance
- Test & Measurement
- Asynchronous counter
