74HC112D,653
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | JK Type |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 4.5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC112 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 71MHz |
| Propagation Delay | 270 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 16 ns |
| Family | HC/UH |
| Logic Function | AND, Flip-Flop, JK-Type |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 30ns @ 6V, 50pF |
| Trigger Type | Negative Edge |
| Input Capacitance | 3.5pF |
| Clock Edge Trigger Type | Negative Edge |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74HC112D,653 Overview
The flip flop is packaged in 16-SOIC (0.154, 3.90mm Width). It is included in the package Tape & Reel (TR). The output it is configured with uses Differential. Negative Edgeis the trigger it is configured with. It is mounted in the way of Surface Mount. The supply voltage is set to 2V~6V. A temperature of -40°C~125°C TAis considered to be the operating temperature. Logic flip flops of this type are classified as JK Type. The 74HCseries comprises this type of FPGA. Its output frequency should not exceed 71MHz Hz. There are 16 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. It is a member of the 74HC112 family. The power source is powered by 4.5V. Input capacitance of this device is 3.5pF farads. This D flip flop belongs to the family of HC/UH. In this case, the electronic component is mounted in the way of Surface Mount. The 16pins are designed into the board. This device exhibits a clock edge trigger type of Negative Edge. The maximal supply voltage (Vsup) reaches 6V. The supply voltage (Vsup) should be kept above 2V for normal operation. The superior flexibility of this product is achieved by using 2 circuits. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. It consumes a total of 4μA quiescent current at any given time.
74HC112D,653 Features
Tape & Reel (TR) package
74HC series
16 pins
74HC112D,653 Applications
There are a lot of Nexperia USA Inc. 74HC112D,653 Flip Flops applications.
- Consumer
- Single Up Count-Control Line
- Shift Registers
- Latch-up performance
- Data Synchronizers
- Power down protection
- Matched Rise and Fall
- Instrumentation
- Memory
- CMOS Process
