74HC175PW-Q100J
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1997 |
| Series | 74HC |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HC175 |
| Function | Master Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Clock Frequency | 89MHz |
| Propagation Delay | 265 ns |
| Family | HC/UH |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Bits per Element | 4 |
| Max Propagation Delay @ V, Max CL | 30ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Clock Edge Trigger Type | Positive Edge |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HC175PW-Q100J Overview
It is embeded in 16-TSSOP (0.173, 4.40mm Width) case. The package Tape & Reel (TR)contains it. This output is configured with Differential. It is configured with a trigger that uses Positive Edge. Surface Mountis occupied by this electronic component. The JK flip flop operates with an input voltage of 2V~6V volts. A temperature of -40°C~125°C TAis considered to be the operating temperature. The type of this D latch is D-Type. In terms of FPGAs, it belongs to the 74HC series. Its output frequency should not exceed 89MHz. There are 1 elements in it. There is a consumption of 8μAof quiescent energy. 16terminations have occurred. The 74HC175family includes it. Power is supplied from a voltage of 5V volts. This T flip flop has a capacitance of 3.5pF farads at the input. In this case, the D flip flop belongs to the HC/UHfamily. The electronic part is mounted in the way of Surface Mount. This board is designed with 16pins on it. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. It reaches 6Vwhen the maximum supply voltage (Vsup) is applied. Normal operation requires a supply voltage (Vsup) above 2V. If high efficiency is desired, the supply voltage should be kept at 5V.
74HC175PW-Q100J Features
Tape & Reel (TR) package
74HC series
16 pins
74HC175PW-Q100J Applications
There are a lot of Nexperia USA Inc. 74HC175PW-Q100J Flip Flops applications.
- Latch
- Divide a clock signal by 2 or 4
- Computers
- Frequency division
- Memory
- Functionally equivalent to the MC10/100EL29
- Control circuits
- Convert a momentary switch to a toggle switch
- Clock pulse
- Circuit Design
