74HC175PW,112
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 1997 |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC175 |
| Function | Master Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Bits | 4 |
| Clock Frequency | 89MHz |
| Propagation Delay | 17 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 16 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 30ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HC175PW,112 Overview
As a result, it is packaged as 16-TSSOP (0.173, 4.40mm Width). As part of the package Tube, it is embedded. T flip flop uses Differentialas its output configuration. Positive Edgeis the trigger it is configured with. The electronic part is mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 2V~6V. In the operating environment, the temperature is -40°C~125°C TA. D-Typedescribes this flip flop. It is a type of FPGA belonging to the 74HC series. A frequency of 89MHzshould be the maximum output frequency. A total of 1 elements are present. There are 16 terminations,This D latch belongs to the family of 74HC175. The power supply voltage is 5V. This JK flip flop has a 3.5pFfarad input capacitance. It belongs to the family of electronic devices known as HC/UH. The electronic part is mounted in the way of Surface Mount. This board has 16 pins. This device exhibits a clock edge trigger type of Positive Edge. The design is based on 4bits. It reaches 6Vwhen the maximum supply voltage (Vsup) is applied. The supply voltage (Vsup) should be kept above 2V for normal operation. If high efficiency is desired, the supply voltage should be kept at 5V. Currently, there are 4 lines of input. In terms of quiescent current, it consumes 8μA .
74HC175PW,112 Features
Tube package
74HC series
16 pins
4 Bits
74HC175PW,112 Applications
There are a lot of Nexperia USA Inc. 74HC175PW,112 Flip Flops applications.
- Parallel data storage
- Dynamic threshold performance
- Data Synchronizers
- Bus hold
- Event Detectors
- Storage registers
- Count Modes
- Reduced system switching noise
- Control circuits
- ESD protection
