74HC175PW,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1997 |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC175 |
| Function | Master Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 4 |
| Output Current | 25mA |
| Number of Bits | 4 |
| Clock Frequency | 89MHz |
| Propagation Delay | 265 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 16 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 30ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Clock Edge Trigger Type | Positive Edge |
| Length | 5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
74HC175PW,118 Overview
It is embeded in 16-TSSOP (0.173, 4.40mm Width) case. You can find it in the Tape & Reel (TR)package. It is configured with Differentialas an output. The trigger configured with it uses Positive Edge. Surface Mountis positioned in the way of this electronic part. A 2V~6Vsupply voltage is required for it to operate. The operating temperature is -40°C~125°C TA. This D latch has the type D-Type. FPGAs belonging to the 74HCseries contain this type of chip. In order for it to function properly, its output frequency should not exceed 89MHz. The list contains 1 elements. There are 16 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. JK flip flop belongs to 74HC175 family. Power is supplied from a voltage of 5V volts. This JK flip flop has a 3.5pFfarad input capacitance. It belongs to the family of electronic devices known as HC/UH. A part of the electronic system is mounted in the way of Surface Mount. This board is designed with 16pins on it. This device has Positive Edgeas its clock edge trigger type. It is designed with a number of bits of 4. 6Vis the maximum supply voltage (Vsup). Normally, the supply voltage (Vsup) should be above 2V. The superior flexibility is achieved through the use of 4 circuits. In order to ensure high efficiency, the supply voltage should remain at 5V. With a current output of 25mA , it offers maximum design flexibility. Despite external influences, it consumes 8μAof quiescent current.
74HC175PW,118 Features
Tape & Reel (TR) package
74HC series
16 pins
4 Bits
74HC175PW,118 Applications
There are a lot of Nexperia USA Inc. 74HC175PW,118 Flip Flops applications.
- Power down protection
- Balanced Propagation Delays
- High Performance Logic for test systems
- Safety Clamp
- Communications
- Event Detectors
- ESD protection
- QML qualified product
- Data storage
- Consumer
