74HC1G66GV,125
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 70Ohm |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC1G66 |
| Pin Count | 5 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 40μA |
| Nominal Supply Current | 50mA |
| Power Dissipation | 250mW |
| Max Supply Current | 50mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 50 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 27 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 80Ohm |
| High Level Output Current | 25mA |
| Low Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 20ns, 20ns |
| Switch-on Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 2V~10V |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74HC1G66GV,125 Overview
The electrical component comes in SC-74A, SOT-753 packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, this analog switch is mounted. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to -40°C~125°C TA. The total number of terminations is 5. As a result of its 1 channels, this electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 5V voltage supply. An injection of 5 pins is performed into the body of the electrical component. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Search with 74HC1G66 if you are looking for analog multiplexer variants. Analog switches have 70Ohm internal resistance. For details about the functions of 5 pins, please refer to the datasheets. A voltage higher than 10V should not normally be supplied to the switches. A cost-effective Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 2V. 40μA current would be enough for this multiplexer to operate. An analogue multiplexer drains from a single voltage supply at 2V~10V. A voltage higher than 50mA may cause damage to the switch multiplexer. A voltage of 5V can be used to operate the electronic component. The electrical component supports 1 inputs.
74HC1G66GV,125 Features
1 Channels
Switch Circuit: SPST - NO
40μA Supply Current
-3db Bandwidth: 200MHz
74HC1G66GV,125 Applications
There are a lot of Nexperia USA Inc. 74HC1G66GV,125 Analog Switches & Multiplexers ICs applications.
- E1 Multiplexer
- MP3 players
- Access Concentrators
- Data Acquisition Systems
- Transmit
- Precision test equipment
- Optical Applications
- High-Voltage
- Relay replacements
- Fiber to the Home
