74HC1G66GW,165
| Parameters | |
|---|---|
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC1G66 |
| Pin Count | 5 |
| Operating Supply Voltage | 5V |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 40μA |
| Nominal Supply Current | 50mA |
| Power Dissipation | 250mW |
| Max Supply Current | 50mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 50 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 27 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 80Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 20ns, 20ns |
| Voltage - Supply, Single (V+) | 2V~10V |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 70Ohm |
| Terminal Finish | Tin (Sn) |
| Max Power Dissipation | 250mW |
| Peak Reflow Temperature (Cel) | 260 |
74HC1G66GW,165 Overview
The electrical component comes in 5-TSSOP, SC-70-5, SOT-353 packaging, which makes it convenient to ship overseas. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, this analog switch is mounted. There is 1:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -40°C~125°C TA. As part of its design, the 5 series is equipped with this electronic component. The analog switch ics are built using SPST - NO switching circuits. Look for analog switch ic variants by searching with 74HC1G66. In this multiplexer, the internal resistance is 70Ohm. For details about the functions of 5 pins, please refer to the datasheets. Multiplexers should not be powered above 10V in normal situations. Analogue multiplexers of the Single supply type that are cost-effective. It is recommended that the electrical component receives a voltage of 2V. For this multiplexer to operate, 40μA current would be sufficient. Using only a single voltage supply, this analog switch requires 2V~10V voltage. If put voltage greater than 50mA on the device, damage may be caused to the analogue multiplexer. 5V operating voltages can be used with this electrical part. Operating 1 inputs is required.
74HC1G66GW,165 Features
Switch Circuit: SPST - NO
40μA Supply Current
-3db Bandwidth: 200MHz
74HC1G66GW,165 Applications
There are a lot of Nexperia USA Inc. 74HC1G66GW,165 Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- Industrial and process control systems
- Communication systems
- Data switching
- Precision instrumentation
- Multi-Line E1 Interface Cards
- Channelized and Unchannelized DS3 applications
- Cellular phones
- Avionics
- Relay Replacement
