74HC273BQ,115
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-VFQFN Exposed Pad |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74HC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Bits | 8 |
| Clock Frequency | 122MHz |
| Propagation Delay | 15 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 26ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 8 |
| fmax-Min | 24 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 4.5mm |
| Width | 2.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HC273BQ,115 Overview
It is packaged in the way of 20-VFQFN Exposed Pad. There is an embedded version in the package Tape & Reel (TR). Currently, the output is configured to use Non-Inverted. There is a trigger configured with Positive Edge. It is mounted in the way of Surface Mount. A 2V~6Vsupply voltage is required for it to operate. It is operating at -40°C~125°C TA. This logic flip flop is classified as type D-Type. FPGAs belonging to the 74HCseries contain this type of chip. It should not exceed 122MHzin terms of its output frequency. D latch consists of 1 elements. There are 20 terminations,It is a member of the 74HC273 family. The power supply voltage is 5V. Its input capacitance is 3.5pFfarads. An electronic device belonging to the family HC/UHcan be found here. There is an electronic part that is mounted in the way of Surface Mount. This board is designed with 20pins on it. This device has the clock edge trigger type of Positive Edge. It is designed with 8bits. It reaches 6Vwhen the supply voltage is maximal (Vsup). Normally, the supply voltage (Vsup) should be kept above 2V. Optimal efficiency requires a supply voltage of 5V. Currently, there are 8 lines of input. It consumes a total of 8μA quiescent current at any given time.
74HC273BQ,115 Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
74HC273BQ,115 Applications
There are a lot of Nexperia USA Inc. 74HC273BQ,115 Flip Flops applications.
- Latch
- ESCC
- Dynamic threshold performance
- Storage registers
- Memory
- Reduced system switching noise
- 2 – Bit synchronous counter
- Data Synchronizers
- ATE
- Balanced 24 mA output drivers
